FMS 1.1M PC-21 PNP Version With Reflex V2 System

The high cost anti-collision design of foam box.
FMS invest not only on the airplane design but also on the foam box. CNC molding for the box makes the airplane parts fit inside the box 100% exactly. Double cost is the difference comparing the normal molding. Two weeks designing on the 3D graph, which makes the final work detailed and quite strong. Before mass production, a series of crash tests against the four angles and six sides is needed. 

Install in 15 mins with absolutely no glue.
Glue is unacceptable to most players. Here we offer you the most thoughtful airplane, which can be assembled with no glue - just a couple of screws. It takes only 10 mins or less to finish installing work for an experienced player, and about 15 mins for beginner. 

99% scaled appearance.
With over one months research on the different resource, the engineers get the most specific and accurate drawing data and work on it. Our team focus on every detail, every skin line, every rivet position, every paint color. 5 blades propeller, retractable landing gear, flaps, scale pilot, all of the above give this airplane more distinction.
 
The latest foaming material
The airplanes in the market are always made with low-ratio & high-density foam particles due to the low cost, which cause the plane heavy and fly not well. PC-21 adopts the latest high-ratio & low-density EPO 52, which alleviates the airplane weight at around 15%, greatly optimizing the flying performance without weakening the airplane. 

The environmental water-based paint
Oil paint is low cost paint which will cause some disadvantages like high corrosion (which deforms the airplane in hot summer), environmental damage, and harm to human health. Water-based paint is non-corroding, environmentally friendly, and safer to human health. This high cost paint could protect the fragile foam parts under any condition. To bring you a green and safe product, water-based paint is now used on this model.

A nicely-controlled PC-21
It is a mutual work of engineers all over the world. The model was unceasingly tested and corrected in the past months. You could operate stably without gyro and land confidently without flap. As long as you are familiar with the remote control, you could fly this model well.

- Material: Durable EPO   

- Wing Span: 1100mm (43.3in)

- Length: 1235mm (48.6in)

- Flying Weight: Around 1,680g

- Servo: 9g Servo x 7 (Installed)

- Landing Gear : Electric Retract Landing Gear (Installed)

- Motor:  3541 750Kv Outrunner Brushless Motor (Installed)

- ESC: 40A Brushless ESC (Installed)

- Propeller: 10 x 7   5 Blade Propeller x 1 Set (Include)

- Battery: Li-Po 4s 14.8v  2600mAh -3300mAh  30C x 1 Set (Not Include)

- Radio: 6 Ch Radio Control (Not Include)

FMS_1100mm Pilatus PC-21 Teaser from Bajora on Vimeo.

Alastair Codd on 30/12/2017

( 5 / 5 )

This rocks on 5 cell 3300mAh, great vertical performance & with mixed throttle use I get about 6min (about 3.85V per cell on landing, so still more in reserve). I can only hope that FMS will release it as a 1400 - 1700mm as well! Everyone at the club loves the scale 5 blade prop, looks great in all those mid-air photos our resident photographer takes. You will not be dissappointed in the quality or the performance.

James White on 16/01/2017

( 5 / 5 )

This is real winner from FMS and RC Castle. Out of the box to flying in less than 20 mins. All bolt together with no glue. The airplane looks fantastic and flies very solid. It climbs really well and goes where you point it. Landings are easy and slow with some flap. RC Castle had this to me in Canada in about 8 days. Great experience all round. Think i will buy only FMS in the future.

Showing 1 to 2 of 2 (1 Pages)

Write a review